收藏本站
Evaluation Kit Hardware
Table 4-22. JTAG/ICE Connector J13 Signal Descriptions
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Mnemonic
VTref. 3.3V power
Vsupply. 3.3V power
nTRST TARGET RESET - Active-low output
signal that resets the target
GND
TDI TEST DATA INPUT - Serial data output
line, sampled on the rising edge of the TCK
signal.
GND
TMS TEST MODE SELECT
GND
TCK TEST CLOCK - Output timing signal,
for synchronizing test logic and control
register access.
GND
RTCK - Input Return test clock signal from
the target.
GND
TDO JTAG TEST DATA OUTPUT - Serial
data input from the target.
GND
nSRST RESET
GND
RFU
GND
RFU
GND
Description
This is the target reference voltage. It is used to check if the target has power,
to create the logic-level reference for the input comparators, and to control the
output logic levels to the target. It is normally fed from VDD on the target board
and must not have a series resistor.
This pin is not connected in SAM-ICE. It is reserved for compatibility with other
equipment. Connect to VDD or leave open in target system.
JTAG Reset. Output from SAM-ICE to the Reset signal on the target JTAG port.
Typically connected to nTRST on the target CPU. This pin is normally pulled
HIGH on the target to avoid unintentional resets when there is no connection.
Common ground
JTAG data input of target CPU. It is recommended that this pin is pulled to a
defined state on the target board. Typically connected to TDI on target CPU.
Common ground
JTAG mode set input of target CPU. This pin should be pulled up on the target.
Typically connected to TMS on target CPU. Output signal that sequences the
target's JTAG state machine, sampled on the rising edge of the TCK signal.
Common ground
JTAG clock signal to target CPU. It is recommended that this pin is pulled to a
defined state on the target board. Typically connected to TCK on target CPU.
Common ground
Some targets must synchronize the JTAG inputs to internal clocks. To assist in
meeting this requirement, a returned and retimed TCK can be used to
dynamically control the TCK rate. SAM-ICE supports adaptive clocking which
waits for TCK changes to be echoed correctly before making further changes.
Connect to RTCK if available, otherwise to GND.
Common ground
JTAG data output from target CPU. Typically connected to TDO on target CPU.
Common ground
Active-low reset signal. Target CPU reset signal.
Common ground
This pin is not connected in SAM-ICE.
Common ground
This pin is not connected in SAM-ICE.
Common ground
Evaluation Kit (EK) User Guide
4-51
11115A–ATARM–27-Jul-11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT91SAM9XE-EK KIT EVAL FOR AT91SAM9XE
AT93C46D-TH-T IC EEPROM 1KBIT 2MHZ 8TSSOP
AT93C46E-TH-T IC EEPROM 1KBIT 2MHZ 8TSSOP
AT93C46Y6-10YH-1.8 IC EEPROM 1KBIT 2MHZ 8DFN
AT93C56A-10TU-2.7 IC EEPROM 2KBIT 2MHZ 8TSSOP
AT93C86AY6-10YH-1.8 IC EEPROM 16KBIT 2MHZ 8MAP
ATAVRBFLY KIT EVALUATION AVR BUTTERFLY
ATAVRXBNDL XMEGA XPLAIN AND DISPLAY MODULE
相关代理商/技术参数
AT91SAM9XE128 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers
AT91SAM9XE128_09 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers
AT91SAM9XE128_1 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers
AT91SAM9XE128_10 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers
AT91SAM9XE128-CU 功能描述:ARM微控制器 - MCU BGA IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
AT91SAM9XE128-QU 功能描述:ARM微控制器 - MCU PQFP IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
AT91SAM9XE256 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers
AT91SAM9XE256B-CU 功能描述:IC MCU 32BIT 256KB FLASH 217BGA 制造商:microchip technology 系列:SAM9XE 包装:托盘 零件状态:在售 核心处理器:ARM9? 核心尺寸:16/32-位 速度:180MHz 连接性:EBI/EMI，以太网，I2C，存储卡，SPI，SSC，UART/USART，USB 外设:欠压检测/复位，POR，PWM，WDT I/O 数:96 程序存储容量:256KB（256K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:56K x 8 电压 - 电源（Vcc/Vdd）:1.65 V ~ 1.95 V 数据转换器:A/D 4x10b 振荡器类型:内部 工作温度:-40°C ~ 85°C（TA） 封装/外壳:217-LFBGA 供应商器件封装:217-BGA（15x15） 标准包装:126